Hydraulic Hose Assemblies Pressure Of Hose Hydraulic Components Unions 3300Bar

                                                                     High pressure hose

Ultra-high safety hoses for ultra high-pressure hydraulics.

AI LE SEN Ultra High-Pressure hoses for hydraulics are spiralized steel reinforced polymer that has ultra-high working pressure with maintained flexibility. Its low volumetric expansion gives fast response time in hydraulic systems while smooth inner bored provides a minimized pressure drop. The small outside diameter makes the hose ideal for tight routing. Each assembled kit is cut to your preferred length, fitted with one of our wide range of fittings and high-pressure couplings.

Configure and order hydraulic hose assemblies with the easy-to-use hose configurator for ultra high-pressure hydraulic hose kits. With the configurator you can easily specify hose fittings, hydraulic quick couplings, nipples and accessories according to your specifications.

Failure or improper selection, or improper use of hose, tubing, fittings, assemblies or related accessories can cause death, personal injury and/or property damage. Possible consequences of failure or improper selection and/or improper use of these Products include but are not limited to:

1.Fittings thrown off at high speed

2.High velocity fluid discharge

3.Explosion or burning of the conveyed fluid

4.Contact with suddenly moving or falling objectsthat are controlled by the conveyed fluid

5.Electrocution from high voltage electric power lines

6.Injections by high pressure fluid discharge

7.Dangerously whipping hose

8.Contact with conveyed fluids that may be hot,cold toxic or otherwise injurious

9.Sparking or explosion caused by static electricity

10.Sparking or explosion while spraying paint or flammable liquids

12.Injuries resulting from inhalation, ingestion or exposure to fluids

Fail-Safe: Hose assemblies and fittings can and do fail without warning for many reasons. Design all systems and equipment in a fail-safe mode so that failure of the hose assembly or fitting will not endanger persons or property.

User Responsibility:

Due to the wide variety of operating conditions and applications for hose assemblies and fittings, AI LE SEN and its distributors do not represent or warrant that any particular hose assembly or fitting is suitable for any specific end use system.

The user, through its own analysis and testing, is solely responsible for.

1.Making the final selection of the hose and fitting

2.Assuring that the user’s requirements are met and that the application presents no health or safety hazards.

3.Providing all appropriate health and safety warnings on the equipment on which the hose and fittings are used.

Handling Instructions:

1.Always treat high pressure hydraulic hose assemblies and applications involving the use of high pressure hydraulic hose as semblies with extreme caution.

2.AI LE SEN high pressure hoses are wire reinforced hoses that operate at elevated pressures and should be treated like a high pressure vessel.

3.AI LE SEN high pressure hoses should always be inspected visually prior to use for frayed, damaged or worn outer covers. If the outer cover is compromised in any     way the hose should not be used in service.

4.End connections should always be inspected visually prior to use for signs of wear, rust, cracks or other deterioration that could cause the end to separate from the hose and become a dangerous projectile. If the end connections are compromised in any way the hose should not be used in service.

5.Always ensure that the maximum working pressure of the hose is not exceeded in the application.
6.Always use clean, filtered medium to prolong the life of the hose assembly.

7.Never use a  high pressure hose that has bubbles, blisters or is kinked.

8.Always clean, drain and coil hoses after use.

9.Never use a CEJN high pressure hose with damage to or wires exposed through the outer cover.

10.Never retain a hose by mechanical means at the sleeves .

11.Never exceed the hose’s minimum bend radius or its maximum working pressure.

12.Never drive over or crush the hose with vehicles.

13.Never use hose assemblies with corroded or leaking end connections.

14.Never use dirty medium in a hose assembly.

15.Never bend the hose pull heavy equipment with the hose.

16.Never let the hose assembly support its own weight when elevated off the ground.

17.Don’t expect  high pressure hoses to last forever. Due to the elevated pressures, components wear out more frequently than standard hydraulic applications.

Recommendation:

Do a pressure test once every two years, even if the frequency of use is not high.

                                                    Be sure to ensure safety!